Strength of Materials
Log in to post new content in the forum.
| Topic / Topic starter | Replies | Views |
Last post |
|
|---|---|---|---|---|
|
Can you help me po to solve this? by dragonicewielder » November 8, 2022 - 9:06pm |
1 |
438 |
by Joselito Cordero Jr (guest) December 28, 2022 - 3:31pm |
|
|
I need guidance in designing a beam supporting specified ultimate moment of 1100 kN.m (doubly reinforced beam) by sanamathalino » March 31, 2021 - 8:34pm |
1 |
675 |
by jayborre October 8, 2022 - 5:57pm |
|
|
Required diameter of solid shaft by Alexander » September 24, 2022 - 9:01am |
1 |
117 |
by jayborre October 3, 2022 - 12:10am |
|
|
Theory of Structure: Area-Moment Method by RavenBaks » January 1, 2022 - 6:26pm |
1 |
1,169 |
by Jhun Vert January 4, 2022 - 2:35am |
|
|
strength of materials: normal stress of hollow circular tube by syed hasnain gillani » February 10, 2021 - 4:40pm |
1 |
964 |
by Jhun Vert August 22, 2021 - 7:31pm |
|
|
I need guidance in solving the ultimate moment capacity (doubly reinforced beam) by sanamathalino » March 31, 2021 - 6:26pm |
0 |
543 |
by sanamathalino August 22, 2021 - 9:51am |
|
|
Please help me solve this problem using WSD (Working Stress Design) Method by sanamathalino » March 2, 2021 - 5:03pm |
1 |
689 |
by Jhun Vert August 22, 2021 - 9:51am |
|
|
Please help me solve this problem: Moment capacity of a rectangular timber beam by candybutcher » January 2, 2021 - 7:47am |
1 |
702 |
by Jhun Vert August 22, 2021 - 9:51am |
|
|
I need guidance in solving the balance steel area by sanamathalino » March 17, 2021 - 12:19pm |
2 |
514 |
by Engr Jaydee August 22, 2021 - 9:51am |
|
|
Vickers hardness: Distance between indentations by salveamigos123 » September 1, 2020 - 2:15am |
1 |
670 |
by Engr Jaydee June 2, 2021 - 4:30pm |
|
|
strength of materials - cantilever beam [LOCKED] by helena amutenya... » November 9, 2019 - 6:10am |
3 |
1,589 |
by Jhun Vert January 15, 2021 - 7:43pm |
|
|
Tapered Beam by Randy_09 » September 6, 2020 - 2:19am |
2 |
849 |
by Jhun Vert January 3, 2021 - 9:18am |
|
|
mechanice by Bryan Paul B Perez » December 17, 2015 - 10:36pm |
1 |
164 |
by Jhun Vert December 28, 2020 - 5:13pm |
|
|
Design a rod and beam,with given stresses. by dankata1231 » January 22, 2017 - 12:21am |
0 |
34 |
by dankata1231 December 21, 2020 - 6:27pm |
|
|
Discussion on: Solution to Problem 535 | Economic Sections by Benjamin_Molina » September 12, 2015 - 12:25pm |
3 |
53 |
by Jhun Vert April 23, 2020 - 2:15am |
|
|
Discussion on: Solution to Problem 130 Bearing Stress by Diyman » June 22, 2015 - 8:12am |
1 |
68 |
by Diyman April 23, 2020 - 2:15am |
|
|
Discussion on: Problem 734 | Restrained beam with uniform load over half the span by amir hamzah » June 18, 2015 - 11:37am |
1 |
64 |
by amir hamzah April 23, 2020 - 2:15am |
|
|
Discussion on: Solution to Problem 313 Torsion by Ahmed Mahmoud » January 6, 2016 - 10:04pm |
2 |
95 |
by Jhun Vert April 23, 2020 - 2:15am |
|
|
Discussion on: Solution to Problem 457 | Moving Loads by Nay Low » September 8, 2015 - 7:10pm |
3 |
85 |
by Benjamin_Molina April 23, 2020 - 2:15am |
|
|
pano po malalaman kung asa ung neutral axis sa flexure formula by Ecarg Ennaillij... » March 15, 2016 - 12:08am |
3 |
36 |
by Nenrald Bernal ... April 23, 2020 - 2:15am |
|
|
Discussion on: Solution to Problem 141 Pressure Vessel by Ronwald Dylan B... » November 30, 2015 - 5:26pm |
3 |
59 |
by Jan Josep Garrido Go April 23, 2020 - 2:15am |
|
|
Discussion on: Solution to Problem 597 | Spacing of Rivets or Bolts in Built-Up Beams by ce-mac » February 19, 2016 - 1:04pm |
3 |
568 |
by Jhun Vert April 23, 2020 - 2:15am |
|
|
Discussion on: Superimposed or Built-up Beams by patranco » August 28, 2015 - 11:32pm |
1 |
147 |
by patranco April 23, 2020 - 2:15am |
|
|
Discussion on: Solution to Problem 625 | Moment Diagram by Parts by cmpsnmsl » December 6, 2015 - 7:11pm |
2 |
95 |
by Jhun Vert April 23, 2020 - 2:15am |
|
|
Discussion on: Solution to Problem 113 Normal Stress by Nathaniel Ceaza... » June 21, 2015 - 9:23pm |
6 |
187 |
by shannylynko April 23, 2020 - 2:15am |
Log in to post new content in the forum.
