Problem 599
A beam is formed by bolting together two W200 × 100 sections as shown in Fig. P-599. It is used to support a uniformly distributed load of 30 kN/m (including the weight of the beam) on a simply supported span of 10 m. Compute the maximum flexural stress and the pitch between bolts that have a shearing strength of 30 kN.
Problem 598
As shown in Fig. P-598, two C380 × 60 channels are riveted together by pairs of 19-mm rivets spaced 200 mm apart along the length of the beam. What maximum vertical shear V can be applied to the section without exceeding the stresses given in Illustrative Problem 591?
Problem 597
A plate and angle girder similar to that shown in Fig. 5-32 is fabricated by riveting the short legs of four 125 × 75 × 13 mm angles to a web plate 1000 mm by 10 mm to form a section 1020 mm deep. Cover plates, each 300 mm × 10 mm, are then riveted to the flange angles making the overall height 1040 mm. The moment of inertia of the entire section about the NA is I = 4770 × 106 mm4. Using the allowable stresses specified in Illustrative Problem 591, determine the rivet pitch for 22-mm rivets, attaching the angles to the web plate at a section where V = 450 kN.
Problem 596
Three planks 4 in by 6 in., arranged as shown in Fig. P-596 and secured by bolts spaced 1 ft apart, are used to support a concentrated load P at the center of a simply supported span 12 ft long. If P causes a maximum flexural stress of 1200 psi, determine the bolt diameters, assuming that the shear between the planks is transmitted by friction only. The bolts are tightened to a tension of 20 ksi and the coefficient of friction between the planks is 0.40.
Problem 595
A concentrated load P is carried at midspan of a simply supported 12-ft span. The beam is made of 2-in. by 6-in. pieces screwed together, as shown in Fig. P-595. If the maximum flexural stress developed is 1400 psi, find the maximum shearing stress and the pitch of the screws if each screw can resist 200 lb.
Problem 594
A distributed load of wo lb/ft is applied over a middle 6 ft of a simply supported span 12 ft long. The beam section is that in Prob. 593, but used here so that the 8-in dimension is vertical. Determine the maximum value of wo if fb ≤ 1200 psi, fv ≤ 120 psi, and the screws have a shear strength of 200 lb and a pitch of 2 in.
Problem 593
A box beam, built up as shown in Fig. P-593, is secured by screws spaced 5 in. apart. The beam supports a concentrated load P at the third point of a simply supported span 12 ft long. Determine the maximum value of P that will not exceed fv = 120 psi in the beam or a shearing force of 300 lb in the screws. What is the maximum flexural stress in the beam?
Problem 592
A wide flange section is formed by bolting together three planks, each 80 mm by 200 mm, arranged as shown in Fig. P-592. If each bolt can withstand a shearing force of 8 kN, determine the pitch if the beam is loaded so as to cause a maximum shearing stress of 1.4 MPa.
When two or more thin layers of beams are fastened together with a bolt or a rivet so that they act as a unit to gain more strength, it is necessary to design the to size or spacing of these bolts or rivets so that it can carry the shearing force acting between each adjacent layers.
Problem 590
A box beam carries a distributed load of 200 lb/ft and a concentrated load P as shown in Fig. P-590. Determine the maximum value of P if fb ≤ 1200 psi and fv ≤ 150 psi.
