# Structural Engineering and Construction

**SEC - Structural Engineering and Construction
Common name: Design**

Engineering Mechanics, Mechanics of Materials, Structural Analysis, Design of Timber Structures, Design of Steel Structures, Reinforced Concrete Structures, Construction and Management

**Situation**

A beam of uniform cross section whose flexural rigidity *EI* = 2.8 × 10^{11} N·mm^{2}, is placed on three supports as shown. Support *B* is at small gap Δ so that the moment at *B* is zero.

1. Calculate the reaction at *A*.

A. 4.375 kN | C. 5.437 kN |

B. 8.750 kN | D. 6.626 kN |

2. What is the reaction at *B*?

A. 4.375 kN | C. 5.437 kN |

B. 8.750 kN | D. 6.626 kN |

3. Find the value of Δ.

A. 46 mm | C. 34 mm |

B. 64 mm | D. 56 mm |

**Problem**

A tensile load of 8000 kg elongates a 1-m long square rod by 1 mm. Steel modulus of elasticity is 2 × 10^{6} kg/cm^{2}. What is the dimension of a side of the rod?

A. 5 cm | C. 2 cm |

B. 1 cm | D. 4 cm |

**Situation**

A temporary earth retaining wall consists of wooden plank driven vertically into the ground. The wall is designed to resist 2.4 m height of soil.

Cross-sectional dimensions of the plank = 300 mm wide × 75 mm thick

Allowable bending stress of the plank = 10.4 MPa

Allowable shear stress of the plank = 0.8 MPa

Unit weight of retained soil = 17.3 kN/m

^{3}

Active earth pressure coefficient = 1/3

1. Calculate the maximum flexural stress.

A. 12.7 MPa | C. 8.6 MPa |

B. 14.2 MPa | D. 10.1 MPa |

2. Calculate the maximum shear stress.

A. 1.11 MPa | C. 0.99 MPa |

B. 0.33 MPa | D. 0.77 MPa |

3. Calculate the minimum thickness of the plank to prevent failure.

A. 90 mm | C. 110 mm |

B. 80 mm | D. 100 mm |

**Situation**

The truss shown in is made from timber Guijo 100 mm × 150 mm. The load on the truss is 20 kN. Neglect friction.

Compression parallel to grain = 11 MPa

Compression perpendicular to grain = 5 MPa

Shear parallel to grain = 1 MPa

1. Determine the minimum value of *x* in mm.

A. 180 | C. 160 |

B. 150 | D. 140 |

2. Determine the minimum value of *y* in mm.

A. 34.9 | C. 13.2 |

B. 26.8 | D. 19.5 |

3. Calculate the axial stress of member *AC* in MPa.

A. 1.26 | C. 1.57 |

B. 1.62 | D. 1.75 |

**Situation**

The bridge truss shown in the figure is to be subjected by uniform load of 10 kN/m and a point load of 30 kN, both are moving across the bottom chord

Calculate the following:

1. The maximum axial load on member *JK*.

A. 64.59 kN | C. -64.59 kN |

B. -63.51 kN | D. 63.51 kN |

2. The maximum axial load on member *BC*.

A. 47.63 kN | C. -47.63 kN |

B. -74.88 kN | D. 74.88 kN |

3. The maximum compression force and maximum tension force on member *CG*.

A. -48.11 kN and 16.36 kN |

B. Compression = 0; Tension = 16.36 kN |

C. -16.36 kN and 48.11 kN |

D. Compression = 48.11 kN; Tension = 0 |

**Situation**

Diagonals *BG*, *CF*, *CH*, and *DG* of the truss shown can resist tension only.

If *W* = 3 kN and *P* = 0, find the following:

1. the force in member *CF*.

A. 4.76 kN | C. 4.67 kN |

B. 4.32 kN | D. 4.23 kN |

2. the force in member *BF*.

A. 3.2 kN | C. 3.4 kN |

B. 3.3 kN | D. 3.5 kN |

3. the force in member *DH*.

A. 2.8 kN | A. 2.5 kN |

B. 2.8 kN | D. 2.7 kN |

**Situation**

Flexible cables *BE* and *CD* are used to brace the truss shown below.

1. Determine the load *W* to cause a compression force of 8.9 kN to member *BD*.

A. 7.80 kN | C. 26.70 kN |

B. 35.64 kN | D. 13.35 kN |

2. Which cable is in tension and what is the tensile reaction?

A. BE = 12.58 kN |
C. BE = 6.29 kN |

B. CD = 6.29 kN |
D. CD = 12.58 kN |

3. If *W* = 20 kN, what will be the tensile reaction of member *CE*?

A. 6.67 kN | C. 0 |

B. 13.33 kN | D. 10 kN |